DIY drip irrigation for indoor plants

Florists and plant lovers, going on vacation, may not worry about their pets. They have an automatic watering system at their disposal. It is designed to moisten plants for a long time without human intervention. It can be purchased at the store or made with your own hands.

Drop watering for indoor plants

Such a system greatly simplifies the care and cultivation of domestic plants. By adjusting the drip water supply, you can simultaneously water more than 15 flowers. All nutrients penetrate the soil in the required proportions.

Dripping auto watering process

Pros:

• simultaneous irrigation of several plants;
• no need to connect to the water supply;
• regulation of the amount of fluid for each plant;
• economic water consumption;
• targeted irrigation of specific areas and pots;
• Scheduled autonomous watering;
• only the roots (not leaves) are moistened.

Before installation, it is necessary to prepare the plant:

• for 3 weeks, stop fertilizing with fertilizers;
• clear the trunk of buds and flowers;
• reduce exposure to direct sunlight.

How does drop watering for potted flowers occur?

Drop watering for indoor plants is used when there is no way to water the plants daily.

Previously, it was used as an additional form of moisture. For best effect, you should check the system for a long time. Only then use such watering as the main.

Drip autowatering is the impregnation of the soil in small portions (drops). The bottom line is pulling the fluid out through the roots. The root system consumes as much fluid as it needs.

The people call this system an automatic pot. It has 2 vessels, which are separated from each other by a barrier. One has water, the other has a plant. Liquid, if necessary, seeps into the soil and is evenly distributed in it. Flowers in such pots are not subject to drying.

Several types of soil moisture are known:

• Top-standard type of irrigation from top to bottom.
• Intrasoil - using droppers, flasks, funnels, etc.
• Root-flow of fluid occurs from the bottom up.

DIY auto watering system from improvised materials

The need to use an irrigation system for indoor plants

Watering is the most important procedure for the nutrition and growth of all plants on earth. Water carries all the substances and minerals necessary for life. Photosynthesis and metabolism are directly dependent on it.

Excessive moisture in the soil can lead to rotting of the root system, disease, and death. The needs of all plants are different. It depends on climatic conditions and the homeland of green pets. Using an automatic watering system for indoor plants, do not worry about the wrong dosage. The plant itself will tell you how much fluid it needs.

Minerals and fertilizers can be poured into the root zone with water. They are thoroughly dissolved so as not to cause clogging of the irrigation system. Fertilizers are administered according to the instructions for the required number of days.

Home plants require constant care. Timely watering comes first in importance.

How to make a drip autowatering do it yourself

To make a self-drip drip for indoor plants with your own hands you will need:

• The filling vessel is plastic.
• Water for use is clean.
• Cleaning of tubes, hoses is carried out weekly.
• After the first installation, the system is completely flushed.
• In case of plant nutrition with fertilizers, tubes and flasks should be cleaned of residues and impurities.

Moisturize multiple pots at once

There are several ways to make a drip autowatering with your own hands:

• Using droppers.
• Ceramic cones.
• Plastic bottles.

Each of the options is convenient and easy to use in its own way.

How to make drip irrigation from medical droppers

Drop watering is best made from a medical dropper. The system has a fluid flow regulator. With it, you can control the level of water supply to the pot.

To install, do the following:

• The vessel is filled and suspended above the level of the pot (it is advisable to use a plastic bottle).
• The tip of the system is connected to the vessel, and the lower part is lowered into a pot of earth.
• The control wheel switches to the water supply state.

Within several days, it is necessary to monitor the level and speed of water supply to the pot. After installing on time, you can not worry about the plant.

Ceramic cones

Ceramic cones are another drip system designed for watering home flowers. The kit includes a ceramic cone, a vessel and plastic tubes. The narrow part plunges into the ground. Water is poured into another part. Thus, the liquid must drain into the earth under pressure. The feed does not need to be controlled.

The only rule is to install the tank at the right height. With high suspension, fluid will flow slowly and poorly moisten the soil. At low, it threatens to excess moisture.

Plastic bottle

The most common and budget way. For the manufacture you will need 1 plastic bottle for 1 pot and a minimum of physical effort:

• Make several holes on the cover with an awl.
• Bury the bottle with the bottleneck down.
• Cut the bottom and pour water inside the bottle.

The roots are moistened and do not need close care.

There is another option with a plastic bottle. Plastic containers are hung at the bottom with their throats down. She attaches the wire to a wooden rail. In this position, the eggplant is in a stable condition and is easier to fill.

Correctly hanging the bottle

Ready Systems

Ready system with hoses, tubes, etc. delivers water from the main source to all connected plants. Its dimensions can be changed depending on the need. Schematically, this can be represented as follows:

1. A-source (crane).
2. B-conductor (hose, tube).
3. C-end point (nozzle, funnel).

A regulator is used to connect. He controls the feed. Irrigation of the soil occurs in a timely manner.

There are 3 types of connection:

• Remote.
• Direct.
• Using the connector.

In specialized stores there are ready-made automatic watering systems, for example, Hozelock. They can be used in the cultivation of both indoor plants in pots (2 pcs.), And in garden areas of 9 sq.m.

Automatic irrigation systems are very diverse.

Blumat

Widely known among gardeners.

Advantages:

• automatic water supply at any time of the day;
• the equipment is easy to maintain;
• durability;

Disadvantages:

• frequent contamination of filters and tubes;
• frequent filling of the tank.

Potted baskets

People call them smart pots. It works on the principle of molecular motion. The system has a reservoir, from which water itself enters the root system.

The root system absorbs fluid on its own

Detailed description:

• The cache-pot consists of 2 vessels: 1 - the decorative flower-pot itself, 2 - the reservoir, which is invisible and performs the function of drainage of the roots.
• Roots reaching the water absorb the required amount.
• Filling occurs through a special hole.
• There is a sleeve to remove excess fluid.

It’s not so difficult to organize drop watering for your favorite indoor plants with your own hands. A flower lover can try to make a watering system on their own, or can purchase all the necessary accessories in specialized stores.